Drip Drip Drip…That Darn Leaky Faucet!

Kenneth Davis
1460

Drip drip drip…that darn leaky faucet!
We’ve all been there, trying to fall asleep and the only thing we can focus on is that dreaded sound: drip, drip ,drip. So you get up and you think I just have to turn the handle tighter to make the drip stop, yea if it were only that easy!
But you don’t need to call a plumber and spend money on a service call with a few easy steps you can become your own “master plumber?
The first thing you need to do is turn off the water supply to the sink, most of the time the valve is located right underneath, if not you need to follow the plumbing line to the nearest shut off valve. If the valve resists being turned, put a drop or two of oil right where the stem disappears into the large nut. Then use a wrench to loosen the nut one complete turn, and tighten it back up by hand. Wait for a couple of minutes and then you should be able to turn the valve off.
The second thing to do is remove the stem from the top of the fixture, then there will be nut that needs to be turned counterclockwise to be taken off. Grasp the handle and turn it counterclockwise, as if you were turning on the water. The whole thing will lift out in your hand. If you have a ball-type fixture, there will be a setscrew on the lower surface of the handle itself, remove the screw. There will be a plastic ring or cap just unscrew and remove then pull out the ball assembly.
Your almost finished, just need to replace the washer, which should still be attached the ball assembly you just pulled out, there’s a screw holding it on so remove that, replace it with the new washer, tighten the screw back on, be sure not to go to tight where the washer starts to become damaged. Reinsert the stem assembly, and twist it firmly clockwise (don’t over tighten it). Tighten the large nut back into place. Turn the water valve back on and that’s it! If it still leaks it may mean you have to replace the valve seat or replace the entire fixture. You will need to purchase a repair kit that you can find at your local plumbing supply or hardware store.
Use the following steps to replace the ball type fixture: Using the end of the screwdriver, lift out the rubber seats and springs. Replace them with the new ones in the kit. Tug the spout off the base by turning it from side to side and lifting up. Then use the screwdriver to leverage the old O-rings off the base. If they need to be cut off, make sure that you clean off any remaining pieces. Roll the new O-rings over the base to replace them. Re-seat the faucet by turning it from side to side while pushing down. Place the ball assembly back in there, and screw the rounded, knurled cap back on. Before retightening the adjusting ring with the special tool, turn the water back on. Then tighten the ring until no water leaks, but don’t over tighten it. Replace the handle, and tighten the setscrew. You should be all set! It’s a good idea before starting this job to go to your local plumbing supply with the make of your faucet just to make sure that all the necessary parts are available.

Feather Wreaths: Attractive And Simple To Make

Dawn Keadic
1106

Feather wreaths can be a strikingly attractive decoration and are surprisingly simple to construct.
A wreath made from feathers (either real or artificial) can take many forms. They range from playful decorative items constructed from artificial pink fuzzy feathers to more traditional looking seasonal door pieces made from the feathers of wild turkeys. The options are nearly endless. A quick look at any major crafts show will reveal hundreds of possibilities. The many different styles of these wreaths make them a consistently popular accent item.
Although there are many different patterns and ways to construct a feather wreath, one of the more simple means to produce one is by using a basic straw wreath form (available at any major craft store) and several large feathers. This approach requires no additional supplies, except a pencil or other device that may be used to poke guide holes into the form.
The wreath maker simply splays out the feathers and creates a ring around the bottom third of the form. Usually, the feathers are inserted at an angle to produce a more organized and attractive final product. After completing the first ring of feathers, additional layers are made using the same pattern. Generally, three or four layers will produce a desirable outcome if the feathers are sufficiently large relative to the wreath form’s size. After all feathers are properly inserted, the wreath maker may add accent items to improve the final performance. The traditional favorite is a bow placed at the bottom of the wreath.
This strategy for producing a feather wreath works wonderfully with large turkey feathers and can produce a stunning seasonal piece perfect for fall and Thanksgiving decoration. However, the technique will work with virtually any kind of feather. For instance, one can create an angelic wreath from white flowers or a fun, colorful craft from a bag of multicolored artificial feathers.
Feather wreaths can be relatively simple to make and produce a wreath maker with a popular alternative to wreaths constructed from leaves, twigs or branches. The exact nature of a flower wreath is limited only by the maker’s imagination.

Garage Door Openers–Buy The Best Gagage Door Opener Only

Aby Matynne2
786

Buying the right garage door opener has not never been more simpler.Whether you want to buy one for residential use or the commercial use read the tips below and buy the garage door opener which ideally suits you .
Also opening the garage door opener has been a big problem until now but the new technology now ensures that its no more a big problem.
Electric power is the most extensively used fuel for opening the garage door opener.
Also what will you do when the power fails.Although not a routine proble but who will predict the ever unpredictable whether changes,lightning and more.
If power failure is your problem and its a recurrent problem then we recommened the 2500/3500 – DC Motor Belt Drive with EverCharge Battery Backup System .Its made by the liftmaster professional.It can work for full 20 cycles 24 hours a day.Now no more outing in the bad whether just because your garage door opener faisl to open.
Also the new addition has been the new motion detecting control panels built by many leading companies now.
Consider the warranty for all these garage door openers.Always enquire if it has a lifetime gwarranty.Most of the times there is a lifetime warranty on belt and motor only but not on the battery which may have a warranty for 1-3 years.
Commercial Vs Resedential Garage door openers
Commercial are used many times a day but resedential may be used not so often. And thereforewe highly recommened that while selecting a commercial garage door opener always go for the one which is more heavily built and extremely durable.
You have belt drive,screw drive and chain drive models.So select the one most ideal for you.
The last aspect I want to cover is who will fit it?
You have 2 options here.You can either fir it yourself if you have the time and patience to do it or hire a professional to do the job for you.
Visit our site www.garage-dooropeners for all the information garage door openers and use our resource centre to make the best buying decision.

Get the Most from Woodworking Tools with Some Useful Tricks of the Trade

John Mann
1929
12:30:13

Many of the great woodworkers have become skillful because they have had the opportunity to watch and learn from a pro. Undoubtedly, serving as an apprentice under a professional woodworking expert is the best way to hone your own skills but not everyone has this opportunity. However, if you have the drive and passion for woodworking, it is entirely possible to become highly skilled by simply reading about the subject. The following includes some useful tricks of the trade that will surely help you to get the most out of your woodworking tools. A woodworking expert is not born; it takes time and some useful hints.
Wood is the woodworker’s most important tool. Without wood, your woodworking tools would have no job and there could be no end product. The first trick to woodworking is knowing how to properly cut plywood, and that involves using the right tools and manipulating the wood in the appropriate way. Different cutting jobs require different blades. Blades differ depending on the number of teeth, the width, angle and the rake of the blade. Before cutting, assess which blade best suits your cutting needs and which one will help you to produce the cleanest cut possible. When you are ready to cut, score the cut first by running the plywood through your saw once, removing only a small piece. The next cut that you make will be much cleaner. To keep a clean line in your cut, use a router. Make sure that your router is fitted with a straight bit as this will help you to achieve a clean line. A pilot bit and a straight edge will also help produce a clean line. You may also want to consider purchasing a panel scoring setup. Some saws can be fitted with a plywood panel scoring setup that is most useful if you cut a lot of plywood. This setup consists of a smaller blade that first scores the surface of the plywood before the wood reaches the cutter.
Once you have your wood cut, it is necessary to sand down the rough edges. You may not realize it, but sandpaper is one of your important woodworking tools. Here are some helpful wood sanding hints. For easy handling, some woodworkers cut their sandpaper into smaller pieces if they have a sanding block or a finishing sander while others fold the sandpaper to rotating sides as it wears down. However, make sure that your sandpaper is not folded so that two abrasive sides touch as this will wear down the paper against itself during use. To prevent this, fold the paper so that the abrasive sides contact only the non-abrasive sides. This simply requires a single cut along half of the sheet.
Once all your wood is cut and well sanded, you are ready to build. Handling wood is not always easy though, but there are tricks that can help you to do the job right. Anyone who has ever tried to nail into the end of board knows that splitting can happen because as the nail is driven into the wood, the wood fibers are forced apart causing the grain to split. Experienced carpenters will flatten the tip of the nail with a hammer before driving it into the wood because a flattened tip will slice through the wood and crush the fibers rather than split them. This woodworking trick is most useful when installing molding and trim.
There are so many tricks of the trade to be learned when it comes to woodworking. You will find that as you begin to amass a larger knowledge of woodworking tips, your projects will start to look better, and you will be well on your way to becoming a woodworking expert. Woodworking professionals will tell you that there exists an important relationship between the tools you use and the wood you handle.

Hanna Instruments

77hydro
968

For over two decades, Hanna Instruments has led the world in water quality measurement and control technology. They provide easy to use but at the same time, technically advanced products for science, education, agriculture and industry.
www.77hydro brings to you a range of instruments from Hanna Instruments, which are easy to order and buy online. These instruments are manufactured after many years of research & development, manufacturing experience and customer service.
Hanna Instruments is rapidly growing to become a world-class, leading manufacturer of water quality instruments with research & development and production & sales offices in over 30 countries. Hanna Instruments has offices all over the world and has gained its reputation because of timely response to market as well customer requirements.
Founded in 1978, Hanna Instruments is well known as an innovator with very basic solutions to testing and analysis of water. The manufacturing facilities of Hanna Instruments have been ISO 9000 certified since 1996 and as such, they have a full range of products manufactured to the most stringent quality requirements. Every product at Hanna Instruments is carefully designed and manufactured with the individual user in mind.
At the moment, www.77hydro features 10 products produced by Hanna Instruments. The instruments are Handheld ph/ec/tds meter, HI991404 ph/ec/tds/temp continuous read meter, Phep 4 waterproof ph/temp tester, Dist 5 Waterproof ec/tds/temp tester, Combo waterproof ph/ec/tds/temp tester, Hanna ph 7 Calibration Solution 230ml, Hanna tds cal solution 1413ppm 230ml, Hanna Storage Solution 16oz., Hanna Electrode Cleaner 16oz. and Replacement ph electrode for Hanna Handheld meters. These instruments are engineered to meet specific user requirements. The price range of these instruments varies from 15$ to 280$. www.77hydro makes it very easy to choose any of these products, order and buy it online.
The charm of Hanna Instruments lies in the fact that though it is technically very advanced, it is very easy to operate. These products can be used by a technical person as well as a non technical person alike. These instruments have a wider user base because application of new technology has made them accessible to one and all. This is the tradition of Hanna Instruments and its commitment to the customers.
If it is state-of-the-art water quality test instruments you are looking for Hanna is your best choice wherever you are. So wait no more and no longer. Just log on to www.77hydro and order your desired Hanna instrument now.
Please call us on our toll free number at (1-877-774-9376)77HYDRO for availability and shipping quote.

Giving Your Home A New Image Can Be Quick And Easy With Furniture Slipcovers

Caroline Smith
860

By fitting furniture slipcovers over your worn or outdated upholstery you can give your old sofas and chairs a stylish new look in minutes. Stretch slipcovers for furniture are designed to be really easy to fit and can be held in place with elastic or ties for a snug fitting finish. If you’re keen to add some vibrancy and style to your home, without too much expense or effort, the answer could be simply adding some ready made slipcovers. With chair and sofa covers you can give well used furniture a fresh lease of life, and transform the appearance of your whole room.
Furniture covers come in a huge range of sizes and designs for all types of seats. For your family room or den there are wing chair, recliner, loveseat and sectional couch slipcovers. Additionally, loads of attractive kitchen and dining chair slipcovers are available to protect your chairs from accidental food or drink spills, as well as adding a touch of elegance to mealtimes. Slipcovers are made from a variety of durable fabrics, many of which are fully machine washable for your convenience. Choices include cotton, brushed twill, chenille or faux leather. There’s sure to be a material that would look great with your decor and color scheme.
Chair and sofa slipcovers come in a wide selection of patterns and colors, from pastel floral prints to colorful country checks. You can change the mood and atmosphere of your room with your choice of slipcover. You can also alter the style of old fashioned furniture, by disguising ugly legs with a skirt for instance. If you’d like a fully coordinated look, you could spend a bit more to get some custom slipcovers made to the exact measurements of your seats. Slipcovers can be an affordable alternative to re-upholstery or buying brand new furniture. And there’s the added advantage of being able to remove and replace them whenever you fancy a change.
If your home is in need of a makeover, slipcovers could work wonders at improving the appearance of an entire room, without blowing your budget.

Getting Raw Land Not A Raw Deal

Dan Auito
143

There is more to buying raw land than meets the eye and more than a few individuals have wished they’d had a second chance upon finding themselves duped, conned, misled, ill-advised, uninformed, oversold, undereducated and often unprepared. They realize, often too late, that a raw land purchase should be properly investigated, evaluated and negotiated using a logical and rational plan.
Let me start by saying I’m not a geologist, soil analyst, surveyor, engineer or land consultant. I’m a passionate real estate investor, licensed agent, appraisal assistant and landlord who purchased various raw lots, as large as a 15-acre parcel, for investment and building projects. In addition, I have consulted with numerous individuals proficient in real estate, who have contributed to my general awareness of the conditions and merits of raw land. We, as small investors, can further use this information to our advantage in wisely choosing land and utilizing it to it’s highest and best use regarding fulfillment of our needs, wants and desires.
This chapter is not a technical sleeper and as such, it will not go so far as to tell you how much lime to add to your soil to adjust PH levels (7.0 is neutral) but it does try to get you thinking about some of the more general considerations that can lead you to further investigate your options using this material as your starting point.
With that said, the first question I’ll ask you is what exactly do you intend to do with this land once you have it? Why are you buying it? What purpose do you have in mind for land? Are you going to build a home, purchase a lot for retirement or investment? Will you acquire considerable acreage for farming or subdivision? Do you want commercial, residential, recreational or agricultural? Will it be in the north, south, east or west?
So your first question should be, what am I, or we, buying this land for? Will it satisfy my, or our, requirements? To get answers to these questions you would best be served by talking to those who will be most intimately involved with the land, such as your spouse, partner, family members, associated owners, etc. Once you have a clear understanding of what the land is supposed to satisfy, then your search can begin. So often people waste their time and effort because the significant partners have such a wide gap in what each person truly wants from the purchase that they never settle on anything or end up with much less than they could have had.
Land can be said to consist of soil, geology, water and climate. Whether you’re looking at beaches, mountains, deserts, high plains or city lots, they all have some basic components. Some of the basic requirements we most often seek are clean air, water, electricity, sewage disposal and trash removal.
Clean air might be construed as freedom from dusty roads, smog, foul smells from industry or landfills, free from noise of traffic, airports and/or neighbors.
Water availability is essential and is often desired for aesthetics as well as drinking, bathing, washing, cooking, cleaning, toilet facilities and watering vegetation. We also enjoy lakes, rivers and streams for recreation. Others enjoy the tranquil sounds that our streams, rivers and oceans can provide. Without a doubt, water availability is a major concern. Note: A 1666 square foot roof can capture 1000 gallons of water for each inch of rainfall; cisterns of all types have existed since the dawn of man.
Electricity is another necessity that we often take for granted. Is a power plant within a reasonable distance from the land or will it cost you thousands of your own dollars to run cables across public lands to get your electricity hooked up? How far are gas and oil suppliers?
Sewage disposal – 25% of our country is on a well and septic system. If you don’t have access to public utilities, will your land support a septic system as well as the water to operate it?
Solid waste disposal – how far is the landfill? Is there a collection service? You can’t burn everything; how will you get rid of it?
Those are the major necessities for modern, everyday living…things that we really need, but can often overlook until after the contract is signed. Others essentials are a telephone, mail delivery, shopping, police, fire station, hospital/emergency services, schools, churches, recreation facilities and access by good roads and highways.
You’ll want answers to questions like those above and county officials such as planning and zoning, community development and building departments are a good place to start. I would also call utility companies about water, sewer, electric and phone, and talk to neighbors, contractors, developers, real estate agents, appraisers and a local surveyor to have some of the more important questions addressed at the beginning of my search. I wouldn’t rely on the sellers to be all-knowing, either.
Again, planning and zoning departments can offer the following: Maps of existing uses, forecasts of future development, lists of planned new roads, utility extensions, locations of planned waste disposal facilities, details on environmental areas and future land uses. They also regulate building codes, curb-cut permits, historic preservation, housing codes, subdivision regulations, tree cutting and zoning laws. They usually have aerial photographs and plat maps that can help you to better identify and evaluate the land in question.
Do you already have your location identified? Will it be in the east where the weather is often wet and humid or out west where it is predominantly arid and dry? Will you be living in cold weather in the north or gravitating towards the southern hemisphere? Concerning location, what are you least comfortable with: Avalanches, landslides, earthquakes, flooding, hurricanes, tornados, tsunamis, volcanoes and/or wildfires? You may want to investigate areas of interest by going to websites like officialcitysites. You will get a better picture of what awaits you concerning it’s economy, environment, population, recreation, educational, medical and employment facilities to name a few.
Let’s assume you know where you want to buy this land, why you want to buy it, and how and when you will use it once you have it. The following general observations, ideas and information may help you to further investigate the alternatives that are available to you in your endeavor to find the land of your dreams.
Raw land is unimproved property; it has no utilities, sewers, streets or structures and usually must be cleared.
Here are (or can be) a few drawbacks that are sometimes associated with raw land:

Negative cash flow; usually the land does not generate any income while you pay the principle, interest, taxes and costs of development.
Tax advantages are scanty as land cannot be depreciated.
Generally, raw land is considered a long-term ill-liquid investment that often takes time before gains can be realized.
Risk of loss on resale can occur if you choose poorly, fail to evaluate and negotiate properly, the economy slips or various other unforeseen events occur.
It is difficult to obtain traditional financing on or borrow against accrued equity.

Here are some possible benefits to raw land:

Land has the potential to experience tremendous appreciation if bought in the way of growth, or if a higher and better use can be achieved.
Owner financing can often be obtained through the seller at below-market rates.
Subdividing can create added value and provide for immediate returns.
Privacy and pride of ownership can provide a secure feeling to the holder.

What is considered good and bad land?
The worst you can buy is swamp or marshland. Most often flat land is the least expensive to develop and the most desired for building purposes. Land with barren rock will increase costs and virtually eliminate a basement just the same as a high water table.
Note: Loamy soil, which consists of a balanced mixture of clay, sand and some organic matter, appears rich and dark in color and is considered ideal for most purposes. As opposed to good soil, you don’t want hard cracking ground when dry and sticky soil when wet. Warning! Check with your state offices for the presence of expansive soils; this stuff cracks foundations in the most insidious ways, leading many to ruin.
Many people are literally being driven to the hills. Granted the views can be spectacular but roads, utilities, water, sewer, and foundations, such as pilings, can add 25-30% to building costs alone, further adding to this already expensive proposition. When considering going vertical, an 8-degree slope is about the limit when concerning building economically on hillsides.
Plots with trees, a view, rectangular in shape, a gentle slope or none and a good location are most often preferred, and streams can boost values by 100% in some cases.
How to determine the value of raw land
Using the appraisers standard view of estimating value can give us some clues, so let’s look at what appraisers do!

Site size and shape, represented by frontage, width and depth.
Corner influence equals visibility for commercial, or privacy for residential.
Plottage, has assembly or combining of parcels been accomplished.
How much land is excess or surplus; surplus has less value than what is required.
Topography: Land’s contour, grading, natural drainage, soil, view and usefulness
Utilities: Sewers, drinking water, natural gas, electric, telephone, cable, etc.
Site improvements: Landscaping, fences, gutters, walks, drives and irrigation
Accessibility: Parking, location, streets, alleys, connecting roads and highways
Environment: Climate, adequate water supply, air quality, streams, rivers, lakes, oceans and the absence of any hazardous materials

An old timer once gave me this advice: He said, “Dan, always try to buy land that is located as close to those amenities that an area is famous for, as that is often the reason people come to certain areas. He lived in Florida and had plenty of beachfront property located in tourist areas, which clearly illustrated his point.
Who has this raw land and how do we find it?
You may start your search by contacting farmers, investors, real estate agents, state and federal agencies, cities with odd lots they need to put back on their tax rolls, bureaus of land management, federal marshals, tax sales, bank foreclosures, developers, property heirs, the elderly, and family and friends. Use your networks and birddogs while driving areas of interest looking for further opportunities to buy.
Property is often advertised through newspaper ads, real estate brokers, For Sale by Owner signs, flyers, bulletin boards, the Internet, etc. A quick note on how not to buy is in order here. I would not recommend buying land from a glossy brochure or big development company as it is almost always overpriced to cover large overhead costs, advertising and profit. Also remember when a building boom is on, land prices rise. You will do much better buying when demand is low. Another caveat is to stay away from land that is advertised outside of its normal market as it is often overpriced or has problems; otherwise, a local buyer would have bought it!
If you want to find the deals, then most often you are going to have to dig for them. A few successful methods may include visiting the county clerk/recorder’s office to search the public records for the following:

New probate filings, use them to contact heirs
Eviction proceedings to contact out of state landowners
Arrests – these people may need money and may also be going away for a while.
Bail bondsman who may have forfeited collateral in the form of land.
Divorces filed, leading to a division of assets
New guardianships to contact disinterested heirs.
Deeds in lieu of foreclosure, private sellers may in turn sell it to you.
Lis pendens means litigation pending, often signaling foreclosure.

You will most often be contacting many of these sources by writing to them. Don’t get discouraged when you don’t get immediate replies, as the average response rate is one reply for every eight letters that you send. The pros will get on lists and pay services to monitor many of these potential sources, however, good old-fashioned detective work does pay off. When researching in this manner, secrecy is one key and fast action using all cash is the other.
A special consideration to note when hunting legally challenged property is to have a title company in addition to the regular search of mortgage. Tax and easement liens also check files for I.R.S. liens, bankruptcy filings and judgment liens.
Quick review
Up to this point we have talked about not getting conned when starting out. We also noted that it pays to understand what everyone wants from the land to start. You are aware that utilities and basic necessities are very important considerations. You know whom to contact to get further in-depth information on properties of interest. You know flat land with natural amenities is the most desirable and economical to develop. You are more familiar with the risks involved with this type of real estate and you also know that rock, marshes and hillsides can be expensive to develop. You have a better idea of how an appraiser begins to determine value and you may have a few ideas on how to find land and the people who own it.
With that said, we are ready to get down to the business of evaluating, negotiating and financing our well-sought piece of terra firma. What follows is a basic checklist. There is more to consider but this will get you off to a running start.
Basic Raw Land Checklist

Get the most recent and valid information available: A copy of the deed containing the legal description with any covenants and/or restrictions.
Get the street address, a plot plan indicating the specific property location, a survey, a preliminary title report, a recent map and any aerial or land based photographs to help you locate fence lines, trails, roads, streams, ponds, building locations, etc. Walk the land to verify, evaluate and correlate what is indicated, also looking for any signs of hazardous waste dumping, burying or burning.
Determine present use in zoning, according to what planning and zoning tells you. Symbols are used to designate uses – here are a few:

A1: Agricultural with single family home
C: Commercial business
CO: Commercial office
FP: Flood plain
M: Industrial
R1: Residential single family
R1H: Residential hillside
R2 : Residential multifamily
RT : Recreational tourist/ Residential transitional

General categories include:

Farm, Ranch and Timberland
Recreational or Resort
Industrial
Commercial/Business
Residential
Mixed use

Confirm who owns it, their full name, address and phone number
Find out what they do; are they a dealer in real estate?
Ask if anyone else is on the title or has authority to act
What are the annual taxes and assessed values?
Ask why they are selling and how long they have owned it
If the owner doesn’t want to sell, ask if they would consider selling a parcel of it.

The preceding is an abbreviated checklist. It is meant to get you started off on the right foot. Many people will research buying a new car more thoroughly than they would when buying raw land; there are many good books that are devoted solely to the subject of raw land. This type of investment is generally not the best choice for the new investor but often times people look to build they’re dream homes away from developed areas and for that reason I have included my two cents here.
Finance considerations $$$
Raw land as opposed to improved property is much more difficult to finance through traditional lenders. The main reasons are that it generates very little income, development costs can be expensive, there are no buildings or improvements that can be used as collateral and it is often considered speculative.
For those reasons mentioned we find that sellers are often our first choice regarding financing. It is typical for a seller of raw land to accept 10% down and the rest to be paid over time at a specified (below market) interest rate. This would be an example of an installment land contract. Other forms are contract for deed, mortgage and note and purchase money mortgages. In these cases, a real estate attorney usually drafts these contracts and a bank will act as an escrow agent to facilitate verifiable records of payments received. The seller often retains the deed until the property is paid for in full.
If you want to investigate bank financing, then you may start out by offering 30% down with a seven-year mortgage, with the bank getting an extra percentage point over and above the current interest rates for standard loans. This may not be accepted but it does give you a starting point to see just what they may be willing to do.
If you plan on building on your land, then having a development plan with an appraised set of blue prints for the project will help the lender in justifying your loan. If you can use equity from other property, then paying substantial down payments may also be an option.
My final words of caution here would be to know values and don’t overpay. Always offer less when possible and research recent sales of comparable properties. The larger a parcel is, the cheaper it tends to get per acre. Ask an agent what an acre of land tends to go for in the area that you are considering; try to buy more than one acre.
When buying residential lots, builders try to keep raw land costs down to 10% of the overall value of the project. If streets and utilities are already in place, then they will use 25% as their guideline. If you can combine or assemble parcels or achieve zoning changes with property, you have a good chance of immediately increasing its value. Always physically inspect the property and do your research before obligating yourself to buy it. Try using contracts with contingencies put in to protect yourself. In essence, these are really options that let you control the deal while you investigate and research the land’s potential to satisfy your objectives. Happy Hunting and buy the high grounds!

Finishing Your New Fireplace Mantel

Carol Agee
1997
12:30:13

Congratulations on your new fireplace mantel! Many people purchase an unfinished mantel so they can paint or stain it to match the décor of their home rather than having the factory paint or stain it one of their standard colors. I have found that after receiving their new mantel, many people have questions and want advice on the best ways to go about finishing a fireplace mantel.
Painting or Staining?
The first decision that has to be made is whether the new mantel will be painted or stained. Typically this decision is made before buying the mantel as different wood types and materials are used in producing a mantel based on if it will be painted or stained. Stainable mantels use wood types known for their grain and appearance and solid moldings because the wood’s grain will be visible. Most people who plan to stain wood want the grain as well as other natural “blemishes?to shine through and would never cover those natural occurrences with paint. Paintable mantels use finger-jointed moldings and less-decorative wood or MDF (i.e. Medium Density Fiberboard) because the wood won’t be visible. Once it is painted, it is really difficult to tell the material used-that is why many contractors and homeowners alike choose MDF as an economical alternative to wood.
Installing the Mantel
While it is not really necessary to finish a mantel after you install it, it does make the job easier if you do this while it is on the wall; it is similar to painting any other wood trim. If you finish it and then mar the mantel when putting it up, you will have to repair it. Certainly many people paint or stain their fireplace mantel prior to installing it. It is really a personal preference.
Whether painting or staining I have put together a list of tips below to help homeowners finish their new fireplace mantels.
Tips for Painting Your Fireplace Mantel
o I recommend using a high quality semi-gloss paint in the color of your choice-but any paint that is used for inside house trim is suitable.
o Have different sizes paint brush available. You will want a smaller brush if your mantel has dentil molding so you can get the paint into the small crevices. A larger brush will help you paint faster and avoid stroke marks in the paint.
o Although priming your mantel is recommend, you do not have to. You can simply apply two to three coats of paint.
Tips for Staining Your Fireplace Mantel
o Test your stain color on an inside area of the mantel before you install it to ensure the color is what you want to achieve. (If you will be using a polyurethane finish over the stain, I recommend testing the polyurethane on top of the stain so you can see the final appearance of your mantel.)
o If sanding the mantel, use a fine (220) grit.
o If applying more than one coat of stain, be sure to let it dry before adding the next coat.
o Once your stain is dry, apply one or two coats of polyurethane (satin or semi-gloss is recommended) or tung oil to protect your finish.
Finishing a fireplace mantel is a rewarding experience; once it is done you can see how the new mantel enhances the look of the room.

Easy Ways to Save Energy

Aldene Fredenburg
1108

With this fall’s spike in oil and natural gas prices and the further impact Hurricane Katrina will have on this winter’s heating oil supplies, it’s become more important than ever to make sure our homes are as energy-efficient as possible.
Luckily, there are a number of easy, inexpensive ways to button up your home for winter. Numerous cost-efficient products on the market for your windows and doors will go a long way toward preserving the heat you generate with your heating system.
Make sure your windows and doors are tight. Self-stick foam weather-stripping at the tops and bottom of windows, as well as across the separation between the top and bottom halves of the window, will block out drafts. Additionally, clear plastic, secured to the window frame with double-sided sticky tape, will also block out drafts and create an air barrier between the window and you.
Additional weather-stripping around all four edges of doors will also help to block out the cold. Also, don’t forget your water heater! You can buy inexpensive padding to wrap around the unit itself, and sturdy foam insulation for all the pipes.
The way you furnish your home can add to your level of comfort this winter. Thick, insulated drapes will cut back on drafts from windows; wall to wall carpeting will cut back on drafts from cold air coming in from gaps between walls and floors; both wall to wall carpeting and thick area rugs will retain heat and add to your comfort.
Believe it or not, you can lose heat through the switch plates and wall plugs in your outer walls. Another inexpensive product will solve that problem; for three or four dollars you can buy insulated pads to install behind the plates. Simply remove the switch plate, pop in the appropriate padding, and screw the switch plate back on. A single package contains insulated pads suitable for single and double on-off switch plates and two-plug outlets.
Experiment with the way you dress and see if you can turn the thermostat down and still be comfortable. Wear warm fleece; keep your feet warm with thick socks and shoes or fuzzy slippers; even consider wearing a hat indoors. You should be able to turn the thermostat down to at least 68 degrees and still be comfortable. If you have an alternate source of heat – a wood, corn or pellet buring stove – consider using it as a primary source of heat.
If you have thermostats in each room, you may want to consider shutting off the heat in unused rooms, or at least lowering the thermostat in those rooms to 55 degrees. If this is an option, be sure to put weather-stripping around the doors to the unheated rooms.
If you’re really strapped for funds, don’t hesitate to call your local human services agencies to find out if you can qualify for home heating assistance. As a taxpayer, you’ve undoubtedly been supporting all kinds of social programs for years, or even decades; don’t let embarrassment prevent you from getting help when you need it. Adequate heating isn’t a luxury, it’s a necessity.
If you take careful stock of the heating problems in your home and take a few simple measures to solve those problems, you should be able to minimize the impact rising fuel prices will have on your winter heating budget. Keep warm!

Great Flower Garden Design – 4 Simple Steps – Part 1

Ian Worrall
1892
12:30:13

A flower garden will bring you endless enjoyment. Not only is it a feast for the eyes, but it can fill your yard with fragrance and butterflies. Your friends will admire you, and you will love to relax at home while you relish your creation.
But if you create your garden haphazardly, you’ll be very disappointed. For example, if you plant the lush, tall flowers on the edges of a flower bed, they will hide the shorter ones within. If you plant a bulb in a shaded area when it needs lots of sun, it will most likely die.
So, a successful flower garden requires planning, but don’t worry, that’s part of the fun. The planning stage gives you the opportunity to bring out your inner artist and problem solver.
The Basic Design Elements
Your design doesn’t have to be intricate. A basic layout is all you need to determine what you will plant in each flower bed. In doing so, you will make decisions about the color and height of each flower, so that you choose not just the color palette of your garden, but the vertical and horizontal dimensions as well.
First, look at each area of your yard to determine the amount of sun and wind it tends to receive. In the areas of most sun, you will choose flowers that love the sun, leaving flowers that prefer shade to the other areas of the yard.
The type of soil you have is another consideration. You will probably need to get it tested in order to know what plants will work for you or whether you need to add other elements to the soil in order to grow your preferred flowers.
You can start by making a simple drawing of your yard and where you would like to plant your flowers. Again, note the amount of sun and wind each area receives, and the size of each area. Next, you might make a list of your favorite colors and favorite flowers. If you know little about flowers, do some research in seed catalogs or online. When you find a flower that you like, search for the answers to the questions below to determine if this particular flower will work in your garden. If not, move on! You will find another that you like just as well, if not better.
Choosing Your Plants
Before you begin buying plants, you need to determine how much you can spend on your garden. Work out a budget so that you don’t over-spend. Then, consider the following questions for each flower:
1. How much does it cost, and will it fit into your budget?
2. Does it grow in your zone?
3. What kind of soil does it need?
4. How much sun does it require?
5. Can it withstand wind?
6. Is it hardy, or does it require special care? If so, do you have the time to provide this special care?
7. How tall does it grow, and will you be able to accommodate its height?
8. How long does it take to achieve a flowering plant?
9. Is it an annual or a perennial, and when does it flower?
Take a look at photos of flower gardens to get ideas, and think about how many flowers you want. You may decide to frame a particular flower with greenery or separate two types of flowers with a non-flowering plant. This is what florists do when they arrange flowers in a vase or basket. They surround the blossoms with greenery almost like the matting of a picture on the wall.
Don’t forget flowering trees and shrubs. These add special interest in your yard, as they give you different vertical heights and horizontal widths. Bear in mind that they tend to take longer to achieve the flowering stage, but it may well be worth the wait. A flower garden is not created in one year’s time. This is a long process that you will always be tending, so you need to enjoy the process as much as the result.